110 watts pd110 series low cost 100% burn-in small size, light weight three wide input ranges overvoltage protection overcurrent protection specification all specifications typical at nominal line, full load and 25? i ntelligent design q uality product xpiq inc. dc/dc converters input input voltage 10 to 20 vdc (pd110 ??series) 18 to 36 vdc (pd110 ??series) 36 to 72 vdc (pd110 ??series) input current 15a (rms) for 12 vdc 9.4a (rms) for 24 vdc 4.7a (rms) for 48 vdc output output voltage/ see rating chart current ripple 1% peak to peak maximum overvoltage provided on output #1 only, protection set at 112-132% of its nominal output voltage overcurrent all outputs protected in short protection: circuit conditions temperature all outputs ?.04%/? maximum coefficient: general efficiency 60% minimum hold-up time 10 msec line regulation 0.5% max. isolation voltage 1000 vdc from input to output environmental operating 0? to +70?* temperature storage -40? to +85? temperature mtbf 100,000 hours weight 670 g without cover * derate linearly from 100% load to 50? to 50% load at 70? ph: 508 429.9883 fax: 800 226.2100 email: sales@xp-iq.com holliston, ma 01746 usa www. xp- i q .com 53 pd110 13/11/02 3:25 pm page 1
model 1, 2, 3 4, 5 6, 7 8, 9 10 11 12 13 pd110-10, pd110-12 output return return output n.c. n.c. key n.c. pd110-13, pd110-14 #1 #1 pd110-16 pd110-23 output common common output n.c. n.c. key n.c. #1 return return #2 pd110-31, pd110-32 output common common output n.c. output key n.c. #1 return return #2 #3 pd110-40, pd110-41 output common common output n.c. output key output pd110-42, pd110-45-1 #1 return return #2 #3 #4 pd110-45-2, pd110-46 notes mechanical details pin chart 1. for output #2, minimum load is 0 a and peak current is shown for 10% maximum duty cycle for less than 60 seconds. 2. pd110 ??& ??series is suitable for 110 watts maximum at 20 cfm forced air cooling or 80 watts maximum at convection cool ing. 3. pd110 ??series is suitable for 90 watts maximum at 20 cfm forced air cooling or 70 watts maximum at convection cooling. 4. suffix codes for mechanical format and input range are as follows: pd110-xxyz: ?x?is the model code from the above table. ??is the input range. (l=10-20vdc, m=18-36vdc, h=36-72vdc); ??is the mechanical format (a=open pcb, c=enclosed) ex: pd110-31mc, 18-36vdc input, enclosed form. open pcb ? enclosed ? output #1 output #2 (1) output #3 output #4 maximum output model vnom imin imax tol. vnom imax ipeak tol. vnom imin imax tol. vnom imin imax tol. power pd110-10 5 v 0.0 a 22.0 a 3% 110 w pd110-12 12 v 0.0 a 9.0 a 2% 110 w pd110-13 15 v 0.0 a 7.5 a 2% 110 w pd110-14 24 v 0.0 a 4.5 a 2% 110 w pd110-16 30 v 0.0 a 3.6 a 2% 110 w pd110-23 +5 v 0.8 a 10.0 a 3% +12 v 5 a 9.0 a 3% 110 w pd110-31 +5 v 0.8 a 10.0 a 3% +12 v 5 a 9.0 a 3% -12 v 0 a 1 a 4% 110 w pd110-32 +5 v 0.8 a 10.0 a 3% +15 v 4 a 7.5 a 3% -15 v 0 a 1 a 4% 110 w pd110-40 +5 v 0.8 a 10.0 a 3% +12 v 5 a 9.0 a 3% -12 v 0 a 1 a 4% -5 v 0 a 1 a 4% 110 w pd110-41 +5 v 0.8 a 10.0 a 3% +15 v 4 a 7.5 a 3% -15 v 0 a 1 a 4% +24 v 0 a 1 a 4% 110 w pd110-42 +5 v 0.8 a 10.0 a 3% +12 v 5 a 9.0 a 3% -12 v 0 a 1 a 4% +12 v 0 a 1 a 4% 110 w pd110-45-1 +5 v 0.8 a 10.0 a 3% +12 v 5 a 9.0 a 3% -12 v 0 a 1 a 4% +24 v 0 a 3 a 8% 110 w pd110-45-2 +5 v 0.8 a 10.0 a 3% +24 v 3 a 5.0 a 5% -12 v 0 a 1 a 4% +12 v 0 a 1 a 4% 110 w pd110-46 +5 v 0.8 a 10.0 a 3% +15 v 4 a 7.5 a 3% -15 v 0 a 1 a 4% -5 v 0 a 1 a 4% 110 w output voltage & current ratings pd110 dimensions shown in inches (mm). tolerance 0.02 (0.5) maximum. input connector mates with molex housing 09-50-3051 and molex 2878 series crimp terminal. output connector mates with molex housing 09-50-3131 and molex 2878 series crimp material. ph: 508 429.9883 fax: 800 226.2100 email: sales@xp-iq.com holliston, ma 01746 usa www. xp- i q .com 54 pd110 13/11/02 3:25 pm page 2
|
